Company Logo

• 목록
• 답변
• 글쓰기
• 게시판 리스트 옵션
  • 수정
  • 삭제

How to Replace a Kia Sportage Replacement Key

The key in many Kia models comes with an electronic keyless entry system built into. The key can be compared to an remote control, and is able to be replaced with a fresh one from a kia replacement car keys dealer or a locksmith.

Key fobs may stop working due to a variety of reasons, including an empty coin battery, worn buttons or buttons, water damage, signal interference and a malfunctioning receiver module. Here are some suggestions to assist you in getting your 2013 kia optima key key fob that is a replacement for the sportage for good.

How do you replace the remote key or smart key?

It doesn't matter if your Kia is equipped with an intelligent key, remote key push-to-start key, or regular metal non-transponder key, the battery in these keys will eventually require replacement. This is especially in the event that your car displays a message that the smart or remote key has low battery power.

It's a fairly simple procedure. To replace the battery on the keyfob remove the mechanical key from the slit at the back of the fob. Then, push the cover off. Inside the key fob there will be the small screw that holds the battery in its place. Using a small screwdriver, loosen the screw and pull out the old battery. Then, insert the new and close the slit on the key fob.

When the key fob is equipped with new batteries and you've tested it, press the lock and unlock buttons. If the doors lock and unlock exactly as you expect, then you're good to go! You can now utilize the hands-free feature to lock and unlock your kia replacement key fob when your fingers get cold or you have to run errands around Brandon.

Not all key fobs might need to be programmed (transponder chips or smart keys). This requires a programing machine that is available only to the automotive locksmith or dealer. Other keys (non transponder metal keys) don't require programming. If you're looking to reprogramme your key, you'll need to record the key code number on the key code tag.

How to replace a battery

If your Kia key fob isn't responding to pressing the lock or unlock button on the fob, this is a clear indication that the battery should be replaced. A battery that is not functioning properly could cause other problems like the check engine light turning on or the engine not cranking. Fortunately, replacing the key fob battery is a relatively easy DIY project that requires only a few basic tools.

Before you begin ensure that your vehicle is turned off and that all doors are closed. Find the small metal or plastic piece at the bottom of the key fob. Jiggle it until the metal key falls out. The key can be inserted into the driver door handle to unlock your car.

To replace the key fob battery, take off the cover at the rear and use a plastic bar tool to loosen the latch holding the black negative battery cable. Remove the old battery and then orient the replacement battery to ensure that its "+" side faces you and the "-", negative side is facing the fob's electrical contacts. Push the new CR2032 battery straight into position and avoid excessive force to avoid damaging or breaking the contacts of the metal.

Once the new battery is installed then turn the key fob off and on in the ignition repeatedly until the door locks cycle. You can then test the Kia's key fob again to make sure it's working as intended.

how much does it cost to replace a kia key do I replace a smart keys

Depending on the model of your Kia Sportage, you may have an ordinary key fob or a smart key. The difference between these is that the smart key is equipped with tiny mechanical key blade hidden within it, whereas the standard fob isn't equipped with. Both key fobs are equipped with a battery that will eventually require changing. Fortunately, it's an easy task that will take about two minutes.

Before you get started it is essential to ensure that you're on a flat surface with sufficient lighting and that your Kia is off. Keep in mind that the fob is made up of tiny pieces that could be thrown off should you not be careful.

The release button for the small size is located on the lower backside. This will either be a circular silver button or a rectangular slot. You can open the key fob by pressing the button.

After the key fob has been removed, you can remove the battery that was in it. The new battery is a CR-2032 that can be purchased online or at your local auto parts store. When you are done it should be possible to lock or unlock your car key kia with your key fob, even if your engine isn't running!

How do you replace the mechanical key

The Kia key fob is an amazing convenience that allows us to lock and unlock our car key cutting and Programming specialist with the push of the button. Like any other device there are issues with it at times. Luckily, there are methods to solve these issues and keep our key fobs in good condition for the long term.

One of the most frequently encountered problems is a dead or dead battery. This could cause your device to stop working or work intermittently. If this is what you are experiencing then replace the battery with an entirely new battery.

If this doesn't solve the issue, try using the flathead screwdriver that is standard to push the plastic casing of the fob open. Be careful not to scratch any internal components or scratch the plastic. Once open, carefully remove the battery that was removed and replace it with a new one.

When the new battery is installed, close and unlock the doors with the mechanical key (every kia fob has an emergency mechanical key that can fit in the slot). Test the key fob to ensure it's working properly. If the fob isn't working, call a dealer or locksmith to help resolve the issue. To avoid a lockout in the future make sure you get an emergency key that can work in all of the trunk and door cylinders.