Company Logo

• 목록
• 답변
• 글쓰기
• 게시판 리스트 옵션
  • 수정
  • 삭제

Reasons Your fiat punto remote key, Suggested Browsing, 500 Key Fob Won't Work

A key fob for fiat ducato replacement key 500 makes it simple to open doors and start your car. There are a myriad of reasons why the key fob might stop working. This could be due to a dead coin battery or damage to the receiver module, water issues, and interference.

This listing is for a NEW replacement fiat panda key Fiat Flip Key Remote - like the Ilco brand that must be programmed professionally by a local locksmith (click here to search for a Locksmith Search). This remote includes lock, unlock and trunk buttons.

Dead Coin Battery

A dead battery is the main cause of your 500 key fob not functioning. Modern key fobs only have a limited range of operation and must be within only a few inches from the vehicle in order to function. If you are further away from your vehicle, and you press the keyfob button, it will not respond, and display the message "Key Fob Not Detected".

If this happens, replace the coin-cell battery (Part Number CR2032) with a new battery of a reputable brand such as Panasonic Duracell or Energizer. You can typically find them at your local hardware store or online.

You can test the battery on your coin-cell by pressing the buttons while you are standing close to your fiat car key 500. The parking lights should blink and the key fob should operate the lock and unlock switches.

If your key fob still isn't working after replacing the battery, it could be water damage that has prevented it from communicating with the module inside your vehicle. Water damage can happen in a variety of ways, such as the simple splash or submerging your key fob in saltwater at the beach. If you suspect that your fob has been exposed to water, put it in a rice bag to draw out the moisture. If this doesn't work, your fob will probably require reprogramming by an experienced auto locksmith or by the dealer.

Water Damage

While the fob comes with rubber seals that keep water out of the electronic chip inside the device, submerging it into the ocean or washing it in a machine could cause water damage. Saltwater can cause the circuit board to short and then end up dying. It's not a good thing to get the fob wet, but don't give it up if you accidentally drop it in water or fail to remove it from your pocket.

Take the battery off first. Clean the electronic chip with isopropyl ethanol or a similar product and dry it thoroughly before replacing the battery. Next, test the fob to verify if it is working. If the key doesn't function it could need to be programmed again. This is usually handled by an auto locksmith or dealer.

If your key is old and has not been programmed for your car, you will need to replace it completely. A professional locksmith for cars can do this job. The locksmith will need to cut the key to match the ignition in your vehicle. They'll also need to reprogram the fob for your car's system. This is a fast and cost-effective process that can be completed in the same day.

Receiver Module Issues

One of the simplest reasons your 500 key fob won't be functioning is that it's out of range. The remote has a maximum range of 30 feet, which means when you're too far from your car it will not respond to your commands. It can be solved by moving closer to your vehicle until it starts responding.

If your fob isn't working after you replace the battery inside the coin, which is also called a "button", "watch" or "button", it may be due to a malfunction on the internal circuit board. Reprogramming your fob can resolve this issue. You can find instructions on how to do this for the majority of vehicles by searching YouTube or consulting the owner's manual.

It could be necessary to replace the metal clips that hold the coin batteries in place. If they lose tension it could prevent your coin battery from being properly seated and cause your remote to malfunction.

In rare cases, the fob may become desync'd with your vehicle due to software problems or hardware issues. This can cause a major trouble, but you could usually resolve this issue by visiting an auto locksmith to reprogram your fob. In some cases they may have to install the software again in your body control module too.

Interference

Interference can also cause the key fob not to receive or transmit signals. This can happen when the key fob is located near a radio transmitter (cell phones or radar detectors) or another source of electromagnetic radiation. The key fob could not work due to a bad connection to the buttons or water damage, or damage to the internal chips.

If your key fob suddenly stopped working, or you have tried everything at home to solve the issue (e.g. You could have a malfunctioning 500 receiver module after you've tried replacing the battery, reprogramming, or using a spare key for fiat 500 key fob. The receiver module, which is located under the dashboard, receives radio frequency signals from your key fob. It converts the signals into electronic commands which are then interpreted by the vehicle.

Fortunately, there's an easy method to reset every single system on board in your 500 device, including the key fob. Disconnect the battery for 15 minutes by taking off first the negative cable and then the positive cable. Reconnect the battery. This will remove any remaining electric current, and also restart the car's computer. This can help get your key fob to work again. If the problem persists it is recommended that you consult an expert technician. They will be able diagnose the exact cause of any issues.