Company Logo

• 목록
• 답변
• 글쓰기
• 게시판 리스트 옵션
  • 수정
  • 삭제

Replacement UPVC Door Handles

If you're replacing your handles or want to add a bit of extra security you can find the right handle for your door. These handles made of upvc are easy to install and meet the minimum 92mm center distance of multipoint locks.

The most important measurements to take into consideration are the backplate fixing centers and key hole dimensions and levers. Check these carefully against your current measurements prior to ordering.

Lever/Pad

Lever pad handles for doors consist of an elongated lever handle on one side and a paddle-shaped handle on the other. These are designed to work with key wind locks, although they can also be fitted to multipoint split spindle door locks (though you will need an additional dual spindle lock case).

After you have picked the right handle for your doors the available finishes will be shown in the drop-down menu. Some styles of handles are not available in all finishes. You should always check the technical drawing and dimensions for the item you are looking to ensure that you receive the correct size and fit.

When choosing a new set of upvc lever pad door handles it is crucial to make sure that they are in line with the PZ (distance between the handle spindle and the center of the cylinder hole) of your existing multipoint locks, as they need to be in the same line to allow doors to remain locked, either from the inside or the outside. Our handles are designed to fit most conventional cylinders, but it is a good idea to double-check before purchasing.

If you are looking to upgrade to dual spindle levers, you'll need to take out the handles that are currently in use and then disassemble the lock case. This will require an additional split inline cylinder. These can be bought separately and we have an entire technical diagram that you can examine in the images for each product.

After you have removed the screws that hold your existing door handle it is recommended to loosen them, and then inspect the mechanism to see the condition it is in. If the screws aren't tight enough it is possible to loosen them even more. Then you can remove the spindle from the handle and replace it with your new old upvc door handles handle. Before putting the handle in position, it is recommended to ensure that it is in the proper position. You can do this by putting your finger into the gap between the door frame and the handle to ensure that it is level.

Lever/Lever

The lever handles for doors are used to operate a multi-point lock with a Euro cylinder. They are found on a variety of double glazing handles upvc doors as well as wooden and aluminium doors. They are equipped with a lever on the inside and a paddle on the outside and are usually supplied in two different types. Sprung - These have a spring cassette inside the backplate to help bring the handle lever to a horizontal position. Non-sprung: These do not have a mechanism to spring the handle lever to a horizontal angle.

To fix a door handle that is sagging, you will need to locate the detent access hole or pin, which is usually a small rectangle or round shape hole or protruding pin that is located on the opposite side of the base plate. Once located you can loosen the set screw using a screwdriver and remove it to release the lever, allowing it to return to the horizontal position.

Once the handle is set horizontally, it is possible to put back the screws. Tighten them to ensure that the handle is securely fixed to the base plate. You may want to apply a threadlocking solution to the screw threads in order to improve grip and prevent them from loosening over time.

Drooping lever handles on door handles can be caused by many factors. The most common cause is that the fixings are too tight which causes the lever bearing to get tangled against the door. It could also be that the levers aren't operated at a straight angle and this is causing the latch mechanism preventing it from fully springing back into action.

Another common cause is that the sprung lever is not working properly. This is typically due to the spring not being in the right position within the backplate. The easiest way to test this is to move the handle and see if it returns to the horizontal position.

It is important to repair any loose door handles as soon as you can. This could lead to excessive wear on the screws and the handle may even be able to fall off the base plate. It is also recommended to tighten loose screws frequently to stop them from becoming looser.

Lever/Snib

The handles for doors made of upvc are also known as 'Snib' handle sets and have a snib button at the top of the lever that you can press down to lock your door if you don't use the dummy lock. They are usually fitted with a Fullex 68PZ (that's 68mm between the spindle centre and lever or lock centre) door lock. We also carry a selection of other door handles with 68PZ from various manufacturers, including Ferco and Fab & Fix.

Change your door handle is a cost-effective option to modernize your home, whether replacing your handles or installing new ones on doors that you've built in your house. There are a variety of styles of upvc door handle available that include traditional levers on backplate, straight or curving short latch and knob handles that resemble dummy knobs for multi point locks which are ideal for French doors.

Rose door handles are circular or oval-shaped versions of lever on backplate handles. These handles for doors are identified by a lever or a knob that is attached to a backplate. The backplate can be removed for concealed fixing.

These handles are available in a variety of finishes, including chrome and coloured finishes, to match your door and other hardware, such as knobs hinges, and bolts. Some handles come with grub screws, which aid in the secure attachment of the knob or lever to the spindle. Some handles are equipped with bathroom spindles that can be used for bathroom locks. They also come with a thumbturn release mechanism, and can be used on bathroom doors.

Mortise

The tubular latch is most likely to be the culprit if your uPVC door handle is slammed shut. It could be due to many things however the most frequent is the lack of lubrication on the latch plate. It is possible to solve this issue by opening the door, spraying lubricant on the lock and handle. It could also be that the latch is loose from the backplate. This is a more complex issue that requires an expert.

A multipoint door handle is a great solution to solve the issue of a stuck door handle. These handles are attached to the faceplate, and are operated with either a thumb turn or key knob that activates the cam that locks the deadbolt. The handles are available in a number of sizes that will fit different types of uPVC doors. They are also available in a variety of attractive finishes to match the hardware you already have. The handles can be bought online or through the local locksmith and are simple to install, with clear instructions.

You'll have to know your PZ size of your cylinder in order to choose the correct replacement handle set. This is the distance in millimetres between the inner edge of the door frame and the centre of the handle hole. You will also need the type of lock for your door, regardless of whether it is a mortise or hook lock. The easiest way to find the correct handle once you know the measurements is to use the filter for brands on the website. This will help you narrow down your options and then you can choose the correct size.

A typical handle set includes an arm comprising two screws of different lengths, drill guides, and installation instructions. Smart versions, like the Igloohome Smart Mortise 2+ come with a mortice lock with a keypad. These are more complex models and are ideal for professionals who install them or adept DIYers. Some handle sets have a range of other accessories, like weather strips, that can be used to improve the appearance of the door.