Company Logo

• 목록
• 답변
• 글쓰기
• 게시판 리스트 옵션
  • 수정
  • 삭제

How to Fix a Loose Door Hinge

The majority of homeowners can Fix Door Hinge a loose hinge. If the screw holes have been smashed and will not hold screws, you may require dowels and wood glue to fix the door hinge.

Clean up any surface that has rust. This will help to keep the dowels in place and give them an adequate base for them to rest on.

Removal of the Hinges

Most hinges on doors can be removed, which makes it easier to move the door from one side to the other or to remove the entire door off of the frame if need be. Anyone with a bit of patience can remove the hinges, but you must be aware of what to do.

If the hinges have been painted, you'll need to remove the paint before you attempt to remove the pins. You may scratch your door if you do not remove the paint. Place the hinges in an stainless steel pot and fill it with water until the hinges are completely submerged. Allow the hinges to sit in the pan for approximately 30 minutes. The heat from the water will soften the paint and make it easier to take off the pins.

After the pins have been loose, remove the hinges and the frame from the door. You can make use of a screwdriver to get the job done, but it is recommended to use a magnetic screwdriver for this task. This type of screwdriver was created to pick up screws made of steel and will make the project speed up.

Before you attempt to remove the hinges it is a good idea to spray them with oil. A simple lubricant can make the process move along quickly and help you remove the pins and screws. This type of lubricant can be found in a variety of hardware stores and home improvement shops.

The number of hinges you need will also depend on the kind of door you have and the way it's installed. Solid-cored and heavier doors will require more hinges while lighter and hollow-cored doors may only need two or three.

Understanding the different types of replacement double glazing hinges will help determine which one is suitable for your particular situation. The hinges on the exterior are designed to withstand the weight of a door, while interior hinges need to be able support lighter loads.

Reattaching the Hinges

Sometimes, a hinge on a door will loosen over time and start to hang crookedly or slide. This can be a major problem, but the fix is usually simple. A simple retightening will usually solve the problem. If the screw holes have been stripped out, it could be difficult to do. A wood dowel could be used to tighten the holes once more.

Start by drilling out the hole you had previously made using an appropriate drill bit similar to the size of the new screw (typically 3/8"). Then, use wood glue and a wooden dowel to fill the hole. The dowel should be cut to a length that is exactly the same as the screw to ensure a snug fit. After that, reinstall the screw and tighten it until the desired tightness. If the door has a tendency to bind the door, then add a second dowel to the gap and repeat the process. Close the door slowly after each adjustment to ensure that the clearances around the perimeter are correct.

You can also use a wooden plug instead of the dowel. It will work similarly, but it may take a bit longer to set up. You can insert a piece of wood which has been cut to the right size. If you don't have a woodworking instrument or toothpicks, you can make use of toothpicks or wooden matchsticks.

Once you have reinstalled the new screw then use a countersink to make the hole for the screw's head smaller so that it does not touch the edge of the door when it's open and closed. This will make it much easier to tighten the screws when reinstalling hinges.

Once you've reinstalled your hinge, make sure to grease it using a dry lubricant to ensure that it doesn't get stuck in the future. Products such as PB Blaster or Liquid Wrench are great options. Apply a thin coating and allow it to soak into the hinge barrel for about 15 minutes.

Refinishing the Hinges

If you're not ready to replace hinges, you could try a few fixes. Check that the screws that attach the hinge plate to both the replacement upvc door hinges frame and the frame are tight. If they're loose, tighten them with a screwdriver or power drill. Be cautious not to over tighten the screws, because this could cause gaps to appear at the trim joints or worse, strip the threads.

If the problem is that the hinge plates are breaking away from the door and jamb it is possible to reattach the hinges by applying wood glue to the back of the plates, and then inserting toothpicks or wooden dowels into the holes. Dowels or toothpicks will give a solid foundation for the screws and prevent the plates from shifting when you drive them into place. Let the glue dry before you can reattach your hinge.

Another reason for hinges that are loose is that the screws are stripped or are missing. This issue can be resolved by replacing the screws. Be sure to use the correct drill bit for the size of the screw hole in order to avoid drilling into other parts of the jamb or hinge.

Once you've reattached the hinge, close the door and examine the gap between the door and the frame. It should be about the thickness of a nickel all around, or less if there's a gap created by a previous upvc patio door hinges that was not properly hung. If the hinges were put in place correctly, this shouldn't be a problem.

If you find that the hinges are loose, try putting an extra thicker shim between the hinge plate and the mounting surface to give an extra inch of space. You can also try removing the hinge pin from the troublesome hinge and then pounding it using a hammer to make it tighter or use the hinge pin from a different angle altogether. You can also lubricate your hinges with mineral oil or jojoba to reduce friction and keep them in their place. Lubricating your hinges periodically will keep them from becoming stiff and squeaky, and can also prolong their life.

Cleaning the Hinges

The friction generated by a hinge's constant movement draws dust particles. These particles may get stuck and accumulate in the moving parts of door hinges, if they're not regularly cleaned and lubricated. The hinge will become stiff and creaky, and its appearance may rapidly deteriorate. Regular cleaning, lubrication and inspections will ensure the integrity and functionality of hinges that are attached to doors.

Examine the hinges for corrosion. If the corrosion has reached the point of destroying surface of the hinge barrel or screw holes, you'll need to replace the hinges. If you're able to save the hinges, you can remove any loose rust by using wire brush and steel wool. Then, apply a commercial rust remover or a homemade solution such as lemon juice on the hinge. Let the solution that removes rust be on the hinges for several minutes to penetrate and dissolve any remaining rust.

If you don't wish to spend money and time replacing your hinges, simply retightening the screws will bring back the hinge's functionality. It might be necessary to add an shim of wood or a dowel to the hinge when the screws have been degraded. Dowels made of wood are round pieces of wood in the form of rods, which are available in different lengths and sizes. They can be purchased online, in stores selling woodworking supplies and home improvement stores.

A shim can be made of a piece of plastic or metal, based on the type of hinge you've got. To make a dowel, cut a wooden dowel to the desired length. You can then dip a dowel into carpenter's adhesive and place it in the hole. The glue will hold the dowel securely in the position.

Before cleaning the hinges, lay down a cloth or towel to protect your flooring from spills. Once the area is protected and dry, clean the hinges using an absorbent sponge or a soft cloth dipped in a mild cleaner or vinegar to remove built-up dirt, grime and tarnish. A toothbrush or small brush can be used to reach difficult-to-reach spots in crevices or tight spots.