Company Logo

• 목록
• 답변
• 글쓰기
• 게시판 리스트 옵션
  • 수정
  • 삭제

Repairs to uPVC Windows

uPVC is a fantastic option for modern homes. They are durable, long-lasting and easy to maintain. They don't get rotten or rusty like aluminum or timber.

Cleaning and lubricating regularly UPVC windows and doors is essential. This will help prevent unnecessary repair costs and also improve energy efficiency.

1. Broken Glass

If the glass in your window is broken it could cause a large deal of damage to your home, which can make it very hazardous and possibly fatal. It is essential to ensure that your windows are in good condition.

For single pane windows, it is relatively easy to replace them, and the new window is usually able to fit into the old frame very easily. However when you have double-pane windows that are anchored by internal beading it will be more difficult to take out the panes that are in place and replace them with new ones. In this instance, you will need to find some plastic spacers that will aid the new pane in being able to fit perfectly into the window frame.

If you are going attempt to remove the glass panes yourself it is crucial to wear the appropriate safety equipment such as gloves that are thick and protective eyewear. You should also lay down a drop cloth before you begin working on the window panes so that any shards fall onto the fabric, not onto the floor, where they could be trampled under.

Once the glass is removed, it's a good idea to cover the gap with packaging tape or duct tape to stop drafts and water from entering the home until a professional is able to come out and repair the window. It also acts as a barrier to prevent any intruders from getting into your home. If the gap is large, you might be interested in a security door that has an integrated window, as it will provide the best of both worlds.

2. Sagging

Upvc windows and doors are a low-cost energy efficient, durable and long-lasting alternative to timber windows made of sash. Over time, they can develop a variety of issues, including sliding. A sagging window in uPVC can cause problems with light, draughts, and even security. If you notice that your uPVC window is beginning to sag it is important to act swiftly to stop the issue from getting worse.

To fix a window that is sagging you can try repositioning the hinges. First, you'll need to unblock the windows to get at the frame. Then, you can remove the top and bottom hinges with a screwdriver and adjust them counter-clockwise or clockwise. Close your window to test the fit after you have moved your hinges. If you are happy with the fit of the window, you can tighten screws to keep them in the right position.

If you can't reposition the hinges, you may require replacing the seal. Rubber seals can dry out and lose their elasticity over time, causing them to loosen. If this happens, it's important to replace the seal as fast as possible to ensure your uPVC windows remain watertight and draught-proof.

uPVC handles may also become loose. This is usually due to screws that have been removed over time, but it can be caused by the handle mechanism wears out. It's relatively simple to fix a loose uPVC handle. You'll first need to close the window and perform a test fitting. The joints at the corners of the sash should be aligned with the joint on the casing. If it doesn't, you can use the screwdriver to loosen up the handle. Then, you can turn the mechanism to position.

3. Water Leaks

If you're waking up to wet floors and damp walls each time it rains it's important to take action. The leaks of water through windows could cause structural damage to your home and also affect your ability to regulate the temperature of your home. The most common reason for leaks in upvc window repairs windows is that the sealant surrounding the frame is either damaged or missing.

This is a fairly simple fix that can be completed by any DIY expert. Depending on the severity of the problem the caulking used previously might need to be removed before a fresh layer can be put on. It is essential to keep in mind that when it comes to uPVC window repairs you should not be tempted to apply too much caulk' as this will only make the area harder to clean and can reduce the efficiency of your energy.

Verify that the drainage holes have no debris in them and ensure that the sill pan is properly angled to allow the water to drain from the window. In more serious cases, you may need to replace the window.

Mold spots and rotten sills are other signs of water leakage. This fungus thrives in damp conditions and can quickly spread across the home.

If the leakage occurs between the double glazed window repairs near me-glazed window, it is more likely the problem is related to the seal, not the frame. It is also possible to be fixed by a uPVC window specialist who will replace the glass seal and regain the full insulation properties of your windows.

4. Faulty Hinges

If your uPVC windows are difficult to open, or slack and open with ease it could be hinges that are at the fault. They can be repaired by any DIYer who is skilled and can be completed in just a few minutes.

Like any mechanical component hinges will wear out over time. Changing a window hinge is essentially a simple procedure, but it is simpler with someone else to help you hold the frame in place.

Check that the uPVC hinges are open and closed in the correct direction. You can do this by looking for the arrow on each hinge. This indicates the direction in which the window should open.

The issue could be caused either by opening the window improperly or due to a poor installation at the factory. Sending us photos via our website is often enough to solve the issue. We are always happy to provide assistance.

It is also crucial to grease the hinges regularly. This can be done by applying a light engineering oil to the hinges. We suggest using a solvent-free lubricant, such as 3-in-one Multi-Purpose Oil. Regularly lubrication will help the window operate and close more smoothly. It can also prevent corrosion and decrease the chance of sticking. This should be done at least every year. WD40 and other solvent based oils are not recommended because they will damage parts of your uPVC window.

5. Draughts

Draughts in windows made of upvc can be caused by a variety of various factors. The hinges may also become misaligned due to wear, creating an opening between the frame and sash. This can be easily repaired by giving them good cleaning, but in the event that they are beyond repair it could be necessary to get them realigned or replaced. The interlock may be unbalanced. This is located on the hinge's side, and could require to be cleaned. In certain instances it is possible to replace the hinges.

These seals are susceptible to wear and tear or get damaged over time, allowing air to escape. Replacement of these with high-quality weatherstripping is a good way to stop draughts. Replace the windows made of upvc with low-emissivity glasses. This will help to regulate indoor temperatures, and reduce draughts.

The last way to reduce drafts effectively is to use a Draught-exclusion device. These are usually made of fabric tubes filled with a filler, which can be hung over your window sill. They can help keep cold air out and keep your home warm and cosy!

With a little regular maintenance and repair your windows made of upvc will continue to provide a great level of security and insulation for your home. However, it is important to recognise that all windows have a life span and eventually, they will reach a point where it is more cost-effective to replace them rather than repair them. So, if you are experiencing problems with your upvc windows, it is best to seek professional assistance as soon as you can.