Company Logo

• 목록
• 답변
• 글쓰기
• 게시판 리스트 옵션
  • 수정
  • 삭제

Patio Door Lock Repairs

Over time, wear and tear can cause lock malfunctions. There are a few simple steps you can follow to restore the security of your uPVC door.

These simple fixes can make your home safer no matter if you adjust the lock or clean the locking mechanism.

Clean the Lock

Although patio doors are a great option to let in the outside and keep out the elements, they can also be security risks when your lock isn't functioning as it should. With time wear and tear, cold and hot weather dirt and debris can take their toll on the lock on your patio door and cause it to become difficult to open. Fortunately, with some minor maintenance, you can ensure your patio door's locks will always work correctly.

It's important to first clean the patio door lock and all moving parts. This helps remove any dirt and coatings that may hinder the lock from functioning in the way it should. Start by wiping the moving parts on your patio door lock using an aqueous cloth. Then, use a scouring cloth or a damp, rough cloth to scrub the areas that are soiled of the door and frame. It is recommended to wipe the entire lock using dry cloths to eliminate any remaining dampness, and allow it to air dry before applying it to the next time.

If your patio door uses pin-tumbler latches You can lubricate it by applying powdered Graphite to the key. You can also apply a Teflon lubricant like WD-40 Multi-Use Product. This type of lubricant is easy to apply, and it won't disintegrate over time. If you're unable find the right lubricant for your lock, use a pencil with larger tip. Insert the pencil into the lock and jiggle it around to distribute the graphite.

Regular maintenance is also necessary to keep the tracks of sliding patio doors free from dirt, dust and debris. These tracks are especially vulnerable to snow and ice which could cause them to become stuck or slack and make it difficult for your patio doors to open and close.

You can clean the track rails and rollers on Sliding Glass Patio Doors Repair patio doors by removing weather stripping that is dirty or damaged. Clean it and replace it. The same is true for rollers on patio doors, which can be cleaned and sprayed with non-stick lubricant in order to allow them to move freely.

Lubricate the moving parts

uPVC French Doors, similar to sliding patio door repair patios, operate using 3 to 4, or sometimes, 5 point locking mechanisms. This includes the handle and lock cylinder that is operated with a key. These doors also require maintenance, and specifically lubrication of the moving parts. This can be done using a thin oil but not WD40. It should be done every year, at a minimum.

If sagging hinges aren't a cause, the door may be skewed and catch or hitting the strike plate hole within the frame. The solution is to take off the strike plate and use an abrasive chisel, which will enlarge the mortise it sits in. This will permit the latch to fit properly into the hole and stop it from rubbing against the frame.

Once the cylinder is cleared of the way and out of the way, measure its width using the help of a book or piece wood that can fit into the gap of adjustment screw above the lock. The outer dimension is the distance from the outside of the door to the center of the cylinder, and the inner measurement runs from the center of the adjustment screw until the end of the cylinder.

Check the lock's length

If your patio door latch isn't able to turn even after cleaning and lubricating, there's a possibility that it's out of alignment with the strike plate hole. Make sure that your door is properly balanced and that the hinge screws are in good condition. In many instances, moving the strike plate upwards or downwards can fix the problem.

Most of the time, the issue occurs when the lock's strike is too small for the latch to properly engage. In this case you'll have to increase the hole using a chisel or hammer and then test the latch to make sure that it contacts the strike plate smoothly without rubbing against or catching on the frame of the door jamb.

Before purchasing a new lock, it is important to determine what kind of mortise lock you currently have. This can be done by looking at the end faceplate and noting whether it is square or round. Look at each screw hole in the existing lock and note their dimensions. This will enable you to locate an alternative lock that is exactly the same size and will fit in your existing hole.

In addition to identifying the mortise lock that is currently in use, you should also examine it for any scratches or bends that may require repairing. A badly bent or damaged latch is more likely than one that has been used a lot to break. Replace the lock if you notice indications of damage.

Once you've checked the lock and decided on the type of replacement you'll need then it's time to begin working on the actual repair. The spindle and handle must be removed from the patio door. Install the new handle. Start by putting in the handle inside, aligning it with the spindle, and then securing it in place by using the two bolts or screws which hold it. Once the handle in the interior is installed, you can install the handle on the outside and screw it in place as well. After you've completed these steps, test the handles to ensure that they open and shut easily and that the latch engages correctly with the strikeplate.

Check the Strike on the door.

The door latch and strike plate are two parts of the lock that work to ensure that the latch is secure the door. If they are not aligned properly, the latch won't latch the door shut properly. Fortunately, this problem is often easy to fix.

First, inspect the holes in the strike plate's receiving to ensure they are free of obstructions such as dirt or plastic plugs. Then, loosen the keeper screws that keep the strike plate in place and allow it to move vertically, but not removing it from the frame of the door. Then adjust the strike plate to ensure that its holes for receiving align with the latch hooks on the door latch. After the strike plate has been adjusted, tighten all screws and test to see whether the door closes smoothly.

These plates are difficult to reach for homeowners who have sliding patio door repair near me patio doors. However, they are essential to secure and unlock your door. These plates are usually placed on the top and bottom of the door jamb, which is where they are used to support the door's latch. The door latch slides into the strike plate and forms an airtight seal. If the strike plate is damaged, rusted or not properly installed, it could hinder the latch from locking the door securely.

A misalignment between the latch and strike plate is the most common reason for the patio sliding door repair lock to not close or stay. This can be confirmed using the "lipstick" test. Apply a little lipstick along the edge of the deadbolt, then cover it with masking tape. The lipstick will leave the mark when you shut the door. This will reveal exactly where the latch connects how to repair patio door lock the strike plate. If the mark is too low or high, you can alter the strike plate.

If your sliding patio door locks aren't working correctly they could be a problem in keeping your home safe from burglars. You need to resolve this issue as quickly as you can. By following these simple steps, you'll be able to fix your patio sliding door repair near me door's lock and restore its functionality within a short time.