Company Logo

• 목록
• 답변
• 글쓰기
• 게시판 리스트 옵션
  • 수정
  • 삭제

UPVC Window Handle Replacement

It's simple to repair a damaged window and door replacement handle using the appropriate tools. It is important to know what kind of handle you have and the spindle's size before you purchase an alternative.

Older uPVC glass windows replacement near me feature cockspur window handles which have a spur that protrudes to secure a wedge-shaped cockspur striker plate. They can be left- or right-handed and should be matched when replacing.

What type of lock and handle do I need?

There are a variety of window handles made from upvc and locks, each with their particular advantages and uses. The type of handle you have will determine how easy it is to open your windows and whether or not the locking mechanism works as intended. As time passes and with regular usage, the window handles made of upvc may become damaged or worn out, rendering them less effective and secure. In some instances, they could even fall off completely. It is crucial to fix your upvc window handles immediately if you begin to notice them falling off. This will prevent potential break-ins and keep your home safe.

It's a task that virtually anyone can perform. You will need some basic tools, but with right knowledge, it is simple and should only take a few minutes. To get started you must determine the type of lock and handle you have on your window made of upvc and then find the perfect replacement double glazing window.

Inline Espagnolette Handles

These are the most common type of upvc handle and are typically located on the outside of your window. They have a flat design and feature an opening that is connected to the locking mechanism of the window frame when turned. Inline upvc handles also have a spindle that runs through the middle of the handle and then into the frame of the window to activate the latch.

Cockspur Handles

These handles are typically found on older uPVC windows and feature a distinctive hook-shaped design. Cockspur handles are attached to the frame of the window with one screw, and are less secure than other types of window handle.

Tilt and Turn Handles

The tilt and turn handles differ from other handles made of upvc in that they can be turned to open the window and then lowered to the window to let air circulate. They typically have a 7mm spindle on the back of the handle. They are available in left and right handed versions.

It is crucial to determine the spindle's size prior to purchasing a double glazing replacement window handles made of upvc. There are a few that are the exact same size. Drop something in the middle of the hole to test the length. This is the largest spindle size that will fit in your windows.

What is the spindle?

uPVC window handles operate similarly like doors, turning the handle to open an opening inside the frame. The window can then be opened and shut. But, at times, these handles can become damaged, particularly when they are frequently used or exposed to extreme weather conditions. This can leave you needing to replace your uPVC handles on windows since they may not operate the window in a proper manner in the future.

There are many different kinds of uPVC handles to choose from, comprising Espag, Cockspur and Spaded handle options. They are made in a variety of ways to fit into uPVC frames. Each handle type uses an individual spindle to lock the window mechanism. It is important to identify the type of handle you have installed on your uPVC windows so that you can replace it with a suitable one.

The base of the handle will inform the type of uPVC it is. A snap-in covers should be over the screw that holds the handle's base in place. After removing this, you will be able see the second screw that holds the base of the handle in place. After both screws have been removed then you should be able to take the handle out of the uPVC.

After you have removed the uPVC handle, carefully unscrew it from the locking mechanism. Make note of the length of the spindle as you'll need to make sure that you buy an alternative that is the same length as your original handle and locking mechanism.

The spindle wears down and becomes inoperable with the locking mechanism. This could be due to damage caused by constant use or a loosening of the locking mechanism, or even rust over time. If this happens, it is required to replace the window handle and the locking mechanism to restore full functionality to your uPVC windows.

How do I remove the old handle?

Window handles can be damaged or broken over time. It is essential to fix them as soon a possible to ensure your security. It is simple to replace a damaged or worn handle. The job can be completed in less than a minute without the need for any special tools.

The first step to remove the old handle is to remove the screw located at the top of the base of the handle. Once the screw is removed, the handle can then be removed from the base. A second screw will be located at the base of the handle. This too can be removed. After these two screws have been removed, the handle will be removed from the base of the window.

Once the old handle has been removed, take the new handle and align the fixing holes with the holes that are currently in the window frame. If there is a sticker or cap on the new handle, take it off it if required and put the handle back in the appropriate position. It is crucial to verify that the handle is working after it is installed. Turn the handle around and make sure that the lock mechanism is activated.

Espag handles come with a spindle that protrudes from the handle and slot into a multipoint locking mechanism inside the window frame. Cadenza windows have a blade with cutouts that fit into the lock mechanism. Cockspur handles are long and hang over the frame of the window or the transom crossmember of the bar.

Once you have installed the new handle, slide the spindle into the window lock and tighten it. Once the handle is securely fixed in place, replace the'snap in' cover and the screw cap (if necessary). When the handle is ready for use, you can open and close the window a few times to make sure it is working properly and securely.

How do I install the new handle?

Switching your uPVC window handle isn't difficult and the process is simple. All you need is an screwdriver and a bit of perseverance. The first step is ensure that the handle you have previously used is in the unlocked position and then remove any screws that are visible, you can replace them with screw caps if needed. After removing the handle, you need to make a note of the length of the spindle that protrudes from the back of the handle. This is crucial as it will determine what type of handle you need to buy.

Espagnolette handles made of uPVC are the most sought-after kind of handle. They feature a spindle that runs through the handle and acts as an internal locking mechanism within the window frame. When the handle is turned, it releases the latch on the window and allows it to open. During regular use and time, handles for espagnolette may be damaged.

Cadenza handles are a second type of uPVC window handle, which is typically used on tilt and turn windows. They have an extended blade that works an interlocking mechanism that is multipoint within the window. They are usually more secure than espagnolette handles since they are only accessible from the inside. They can be replaced by the same procedure as espagnolette handles however you will need to ensure that the new handle has an angled blade as opposed to a flat one.

Once you have selected the correct handle, you can align the new handle with existing screw holes prior to fixing it with screws. After that, you can put the screws on and test the new handle. You can accomplish this by dragging the handle back and forth from the locked position to the unlocked for a few times. It might be worthwhile to speak with an expert to determine if you can resolve any problems. They can often advise you on the best solution to resolve the issue in a quick and efficient manner.